trek madone 9.0 size chart

Item added to your cart

3 fundamentals of correct bike size - 2022 trek madone.

The following chart provides a rule of thumb approach to determine your 2021 Madone bike size based on your height. This is a simple approach to a complex situation, but it is accurate in the majority of cases. Of course, the length of your limbs is not factored into the table below and long or short limbs or torso can play a big role in determining the right bike size for you.

In addition your riding style can influence your choice; if you like a more aggressive bike, you may prefer a smaller frame; if you prefer a more upright position, you may prefer a large frame. If you are 'between sizes', give this consideration when making your selection. 

The 2021 Trek Madone is produced in sizes 50, 52, 54, 56, 58, 60, 62  

2022 Trek Madone Road Bike Size / Fit Basics

Before you purchase your new road bike, you need to ensure the frame meets 3 basic size requirements: stand-over, reach, seat height. 

1. Stand-over

Stand-over is the measurement of the height of the bikes top-tube from the ground at its midpoint.

Ok, so why is it so important? Simply put, if you are travelling along on your bike and you need to stop in a hurry, you'll have to jump forward, landing on the ground, standing with your legs on each side of the top tube. Having the correct Stand-over will ensure you do not impact your groin area during this situation. 

How to test it.

When you stand-over the midpoint of the bike, with shoes on, you should be able to lift the bike up until there is a 2 cm gap between the tyres and the floor - without the frame coming in contact with your groin. 

If you are looking at the best size option based on a geometry chart, measure from inner leg to floor (with shoes on), remove 2cm and test that measurement against the bikes geometry chart. For the Trek Madone, this is measurement L in the Geometry diagram below. 

Get this one wrong, and you may be in for a world of back pain. Whether that is upper or lower back pain will depend on whether you buy, or are sold , a bike that is too big or too small for you. Buy the correct size bike and your hours of saddle time will actually strengthen your core and back, not hinder it. 

The Reach is the distance your hands project forward to comfortably rest on bars and manipulate the brakes and gears. 

How to test it. 

The quickest test of correct reach is to sit in the correct riding position on the bike (a trainer is great for this or if that is available, take the bike for a quick ride or balance against a wall with someone's assistance).  

Sit on the bike in a neutral position with your hands resting on the hoods (illustrated above) and your head in a natural riding position - eyes looking forward. Now look down at the front wheel hub/axel. If the position is correct the bars should block your view of the hub/axel. If you can see the hub/axel in-front of the bars, the bike is too small.  If you can see the  hub/axel behind the bars, the bike is too large. 

Stem length obviously plays a role here. However, if you are buying a bike from a store, it should be equipped with the correct size stem for the frame. Ideally, you should only have to swap stems if you have a particularly long or short torso. 

Your saddle can be moved forward or back on the 'rails' to make small adjustments to your reach outcome. If the bike is the correct size for you, you should not have to move it all the way forward or all the way back. 

3. Seat Height

Seat height impacts on comfort and performance - correct seat height optimises both. Your seat needs to allow for an efficient and powerful pedal stroke while maintaining you in a balanced, static and comfortable seated position. 

It is also important to note that your seat needs to be in the correct position to properly determine your reach (above). 

This is a simple and quick way to ensure a powerful and efficient seat height position. Sitting on your bike, rest your heal on your pedal when it is in the lowest (6 O'clock) position.

You need to check two things now and you will need another person to assist with this. Check that your leg is fully and comfortably extended. At the same time, when viewed from behind, your hips should be level. If required, adjust the seat height to achieve the ideal balance of full leg extension and level hip placement. When this is resolved, returning you foot the usual cleated cycling position should achieve the correct amount of knee bend.

One Extra! - Bar Drop

The position of the bars relative to the seat. This is the bike fit positioning that can cause a lot of trouble and one that we recommend determining over time and with the assistance of a professional bike fitter.

If you are new to cycling with average fitness and flexibility, err on the side of positioning your bars at the top of the steerer with one spacer above the stem. This will allow options to lower the bars over time as your fitness, flexibility and riding continue to evolve.

Does this position influence which size bike to purchase? That should be a secondary consideration after first determining which frame geometry is appropriate for you. If your flexibility is limited (or not what it used to be), you may be best to consider a frame with endurance geometry to ensure a higher front end and a more relaxed position on the bike. 

Trek Madone SL6 & SL7 Geometry Diagram

Trek Madone SL6 & SL7 Geometry Chart

Trek madone sizes  50,  52,  54,  56,  58,  60,  62.

 Trek Madone SL6 & SL7   Size Chart

The following chart provides a rule of thumb approach to determine your bike size based on your height. This is a simple approach to a complex situation, but it is accurate in the majority of cases. Of course, the length of your limbs is not factored into the table below and long or short limbs or torso can play a big role in determining the right bike size for you. 

Trek Madone sizes 50, 52, 54, 56, 58, 60, 62

Compare to your bike .

If you already own a road bike and are happy with the fit. It is good to know you bike fit basics by measuring your seat height, reach, and bar drop.

Seat Height  - Your seat height is the distance from the centre of the bottom bracket to top of the saddle when running the tape parallel to the seat post. See the purple line in the diagram above.

Bar Reach   - The distance from the front tip of saddle to centre of the bars (where the stem cap contacts with the stem). Keep the tape running parallel to ground. See the green line in the diagram above. 

Bar Drop   - The handlebar drop is the distance from the centre of the bars to the centre of the hub. See the red line in the diagram above.

Once you have these recorded, you can then quickly check how your bike setup will work with the bike you are test riding, renting or just throwing a leg over in a store. 

About Livelo

We don't sell new road bikes, but we do work with a lot of bike brands across our global road bike rental business. We fit thousands of our clients on bikes each year across a broad range of brands and road models. Based on this experience we know there are lots of great bikes available in todays market, but getting that one that is just right for you is a complex. You have to satisfy, the body, the head and the heart.

We are happy to give you some unbiased advice on your road bike needs. We won't be trying to sell you a bike, we will be trying to be helpful. You can contact us here if you would like to talk bikes, 

We do have Trek Madone's available for rent/test ride a in Thousand Oaks , San Mateo , Arlington, Washington, and Canberra  and can help out in many cities in addition to this. Just reach out. 

• Choosing a selection results in a full page refresh.

• MAGAZINE OFFERS
• BIKE INSURANCE
• Best Products
• Maintenance
• Accessories
• Long-Term Reviews
• BikeRadar Podcast
• First Look Friday
• Bike of the Week
• Tech Features
• Routes and Rides
• Bike Galleries
• BikeRadar Bargains
• Buyer's Guides
• Fitness & Training
• Sizing & Fit
• Mountain Biking UK
• Cycling Plus

Trek Madone 9.0 review

A magic carpet ride — if you can fit within the parameters

Ben Delaney / Immediate Media

Ben Delaney

Tangibly fast and blatantly comfortable, very good braking for aero calipers, well-thought-out integration

Steep price, tight fit parameters, toe overlap

The Trek Madone is the most comfortable aero bike I've ridden by a long shot, and its ultra-clean front end and massive, sculpted tubing deliver not only a fast but a luxuriously quiet ride. There are no sloppy cables whistling in the wind here.

The catch? This magic carpet comes with a tight fit window: the front end is a touch high for a race bike, the seatmast's vertical adjustment is limited, and the front wheel has toe overlap and a limited turn radius. But if you fit, you will fly.

• Tunnel test video: How slippery should your aero road bars be?
• How to ruin an aero road helmet (don't do this!)
• 10 of the best deep aero wheels lab tested

Trek Madone 9.0 highlights

• Same frame and fork as $12,000 / £12,000 / AU$13,499 Madone 9.9
• Normal stem and adjustable aero handlebar
• Shimano Ultegra group with Madone Aero brakes
• Bontrager Aeolus Comp Tubeless Ready 50mm wheels
• 50-62cm sizes, four color options
• $3,999 / £3,500 / AU$5,499

One Madone that breaks (a little) free of certain fit constraints

In late 2015 Trek overhauled the Madone as an ultra-aero race machine, with not only cables but the brakes themselves hidden from the wind. The bike received plaudits from several cycling outlets includin g BikeRadar for its aero performance and its comfort, thanks largely to Trek's IsoSpeed flex design, which allows the seat tube and seatmast to flex as one.

But while the bike managed to avoid the typical pitfall of early aero bikes — they're fast, but they ain't comfy — it did proceed with a typical aero compromise of ergonomic adjustability in favor of an ultra-clean integrated bar/stem that is demonstrably faster.

For context, most major companies with a high-end aero bike sell it with some form of integrated bar/stem, for the same reason: it's aerodynamically faster than a round bar and normal stem by a significant margin. Most companies claim at least a 4-watt improvement. (A good aero bike has a total drag number in the 70-watt range.)

And while integrated bar/stem cockpits work well for many riders, some people would prefer particular bar shapes, or bar angles, or at least the ability to make changes. With an integrated design, you get what you get.

The Madone 9.0 is the first Madone to come with separate bar and stem components. Yes, it's marginally slower in a wind tunnel, but you can easily adjust the bar angle or, like I did, replace the stock stem as needed.

Front and rear fit constraints — versus the competition

Like most of the other Madone bikes, the 9.0 comes in Trek's H2 fit. The lower H1 fit is only available in Project One, which adds $1,500 to the price.

As such, the Madone 9.0 has a slightly taller stack height than other aero bikes. Stack is the vertical difference between the top of the head tube and the center of the bottom bracket. Front-end height comparisons are often done with head-tube measurements, but this doesn't account for differences in various bikes' bottom bracket heights.

For comparison in size 56cm bikes, Canyon's Aeroad has a stack of 55cm, Specialized's Venge ViAS a 56.4cm and Cervélo's S5 a 56.5cm to the Madone's 58.2cm.

All the Madone sizes have a relatively tight saddle adjustment window. The 56cm bike has a saddle height range of 67-76cm.

For me, at 6ft with short legs, I had the saddle all the way up to 76cm and a 120cm stem all the way down, and would have appreciated another centimeter or two of handlebar drop. Fit, of course, is highly personal — just be sure the bike always fits you, whatever it is!

Aero brakes: decent power and, gasp, a delight to work on

Trek isn't the first company to experiment with hiding the brake calipers from the wind, but I believe they have done the best job thus far. By extending the frame's front section to house the front brake cable, Trek reduced drag substantially compared with bolting a standard caliper on the front of the fork.

The little cuckoo-clock panels flip open when you turn the bars, allowing the brake and housing room to move. (No cuckoo bird pops out, though, unfortunately.)

I hate rim calipers positioned underneath a frame's bottom bracket. At best, they are a chore to work on, and quickly gather grime. At worst, they are a literal drag, causing brake-pad rub when out of the saddle. Trek keeps the Madone's rear brake where it should be — up on the seatstays.

The power is decent for a rim brake. A Dura-Ace caliper it ain't, but modulation is predictable. The spectrum of aero brakes runs from horrible/dangerous to pretty good. These are pretty good. I tested the bike quite a bit with carbon wheels as well, where the power is adequate when used with SwissStop pads.

Perhaps most surprising to me was how easy it is to work on the brakes. Swapping and then adjusting the pads is easier than on most standard calipers. Seriously. In the absence of a barrel adjuster, Trek has a screw to adjust width on each side, and another to adjust toe angle.

Ride quality: a magic carpet

By now, you have probably seen enough aero-drag graphs and charts to understand that aero shapes are faster than round shapes, especially at higher speeds. I did not take the Madone into a wind tunnel, but my friend Dan Cavallari at VeloNews did. You can get his data and conclusions versus the Specialized Venge ViAS here . I did take the bike out for a few hundred miles, often on fast group rides and solo jaunts, and the thing is tangibly faster than a round-tubed bike with box-section wheels. During the year I switch between a number of test bikes, and the back-to-back rides really highlight differences.

Two things stand out with the Madone. It's fast! (Of course, your body position is the major factor here. But with that normalized, the Madone is perceptibly quick.) And two, it is more comfortable than many standard road bikes, never mind aero bikes, thanks to the full-flexing seatmast and seat tube.

I have an older Scott Foil that I love racing crits on, and while I ride it on dirt roads, it's not my first choice for mixed-surface riding. The Madone, on the other hand, I'd take on any ride.

With Trek's stout BB90 chassis, you still get plenty of firm pedaling efficiency when in and out of the saddle.

The wheel depth of the Bontrager Aerolus Comp 5's is manageable in crosswinds. I rode the bike on many gusty days and did a few days with Mavic's new 65mm Comete Pro Carbon SL tubeless wheels . On one fast group ride, I managed to plow straight into a pothole deep enough to crack the Mavic rear rim . After checking everything out — and opening the rim brake caliper — I rode back home without incident. Would I have crashed on a stiffer aero bike? Who knows. But I can say it is nice to have a forgiving frame underneath you when unexpected bumps and holes appear.

Wheels and components

The Bontrager Aeolus Comp 5 wheels can be set up tubeless but come with 25mm standard clinchers and tubes. Although not as light as all-carbon hoops, the aerodynamics of the metal-rim-with-carbon-fairing design are very similar. And you get the more consistent braking of an alloy track. A downside is that they can take in water at the spoke holes. (There is a hole on the side to release the water.)

Current-edition Shimano Ultegra continues the Japanese company's fine tradition of an excellent second-tier group that for all intents and purpose functions very much like Dura-Ace but with a few more grams. My one gripe with the mechanical Ultegra is how the inner shift lever on the lefthand control can pop slightly outside the primary brake lever on rattling roads. It doesn't affect performance at all, but it's annoying. Dura-Ace levers don't do this.

One curious spec choice is the compact 50/34t crank. When paired with the 11-28t cassette this is a great everyday setup, but it seems like amateur racers, in particular, would be drawn to such an aero bike. They might want, if not necessarily need, a 52/36t crankset. If this is a concern, it is likely that your local Trek dealer could swap it out for you. I suspect that, like the H2 geometry, Trek studies customer fit data carefully, and makes decisions based on the bulk of rider numbers.

Bottom line: Certainly the most comfortable and among the fastest aero bikes on the market

The Trek Madone fuses two seemingly incompatible traits: it is a very fast and very comfortable bike. The 9.0 build is the most inexpensive — but still not cheap — model, and the only one with separate and therefore adjustable stem and handlebar.

If you want to look at third-party aero numbers, check out Dan Cavallari's VeloNews piece where he put the top-end Madone against the top-end Specialized Venge ViAS in the A2 Wind Tunnel and found the Venge to be faster . For context, A2 found both to be faster than Cervélo's S5.

The fit, as discussed, is Trek's H2 geometry, which is slightly higher at the front end than other aero bikes. As with Trek's Emonda, a lot of riders will get toe overlap on the Madone, because of its short and sharp front end. So investigate carefully before you buy — but if everything fits, I doubt you will be able to find a bike as fast and comfortable as this one.

Share this article

Contributor

• Terms & Conditions
• Subscribe to our magazines
• Manage preferences

• Rider Notes

2017 Trek Madone 9.9

A carbon frame aero bike with ultra high-end components and rim brakes. Compare the full range

Manufacturer Price

For This Bike

View more similar bikes →

Based on frame geometry and build specs.

A bike with lower gearing will be easier to ride up steep hills, while a higher top end means it will pedal faster down hills.

Similar Bikes

(descending)

Add custom gearing

5'1" – 5'5"

5'3" – 5'7"

5'5" – 5'9"

5'7" – 6'0"

5'10" – 6'2"

6'0" – 6'4"

6'2" – 6'5"

🐐 Estimated

Do you have this bike? Help other riders make a decision about which size will work for them by sharing your own size and fit notes. Report your fit

Jul 2018 · Philippe Tremblay

New aero road bike gets features for increased comfort, customization and aerodynamics

Read Review

Feb 2018 · Peter Stuart

The Trek Madone 9 is a rather special aerodynamic redesign of the flagship Project One bike.

Dec 2017 · Ben Delaney

An exceptionally smooth and fast aero bike, but with a relatively tall front end, toe overlap and limited saddle-height adjustment. Buy if you want a comfortable aero bike with an adjustable handlebar

Tangibly fast and blatantly comfortable, very good braking for aero calipers, well-thought-out integration

Steep price, tight fit parameters, toe overlap

May 2016 · VeloNews.com

The new Madone is cycling’s Bugatti Veyron — an exotic beast that looks like it’s moving fast even when it’s standing still. This bike begs for high-speed

Apr 2016 · Robin Schmitt

In a country where awesome is standard vocabulary, how could you describe an extraordinary bike? It’s time to look at the hard facts of the Trek Madone 9.9

Apr 2016 · William Tracy

The new Madone is cycling’s Bugatti Veyron — an exotic beast that looks like it’s moving fast even when it’s standing still.

Aug 2015 · Mat Brett

Stunningly good bike that offers a fabulous mix of speed and comfort, although, as usual, the top-end tech comes at a price

In the build-up to this year's Tour de France we see yet another bike launch from one of the big players of the industry. This time it's Trek with the launch of the company's 2016 edition, 9 Series Madone. CyclingTips' Dave Everett was in The Netherlands for the launch and wrote this about his first impressions of

Last updated July 21 Not listed for 2,464 days

First Look and Ride: 2016 Trek Madone 9-Series

Trek shoots for the moon with its new aero road bike

It was a Friday afternoon in late May and I was sitting in the atrium of Trek’s Waterloo, Wisconsin headquarters. I was there to get my first look at Trek’s new 2016 Madone and, during a small break in the action, catching up on some email. A meeting-room door opened to my left, and I watched over 100 men and women stream out. “Company meeting?” I asked my handler, Royce Breckon, Trek’s service brand manager. “Nope,” he said, “Engineering department meeting.”

As I would later learn, Trek has about 80 engineers worldwide; when support staff is counted, Trek’s engineering department employs about 200 individuals. While not all of them were involved in the creation of the new 2016 Madone 9-Series, this gives you an idea of the resources and horsepower that the company was able to put into its new aero road bike—and most ambitious model to date.

Trek has very high aspirations for the new Madone, calling its release, "the biggest launch in Trek’s history." Its tagline is “the ultimate race bike,” and to try and reach that benchmark, Trek considered aerodynamics, handling and rider comfort.

     Related:  Pro Cyclists Debut 2016 Trek Madone 9-Series

The frame is carbon composite, naturally, and the design is highly integrated in the pursuit of (claimed) class-leading aerodynamics. The new Madone also gets Trek’s IsoSpeed Decoupler—a seat tube decoupled from the top tube and seatstays so it may flex further and more easily, increasing vertical compliance—which was originally found on the Domane.

The 2016 Madone will be offered in two variations. One uses Trek’s highest grade 700 series carbon and the company’s H1 long-and-low fit, and is made in Waterloo, Wisconsin. The second is made of 600 series carbon and uses Trek’s H2 fit–taller stack and shorter reach compared to the same size in H1–and is made overseas.

The difference, besides fit: The H1 bike is a 100 grams lighter, and in Trek’s testing appears a bit stiffer and a bit more vertically compliant; however, on the open road, the two ride very similarly, says Michael Mayer, Trek’s global road brand manager. Both are considered the company’s top of the line 9-Series frames, but Trek says the customer who wants the H1 fit is more race-oriented and desires every bit of weight savings. A women’s version will be offered; however, it uses the same geometry as the standard H2 with some spec adjustment.

Trek claims a 56cm H1 Madone frame weighs 950 grams, and that a complete 56cm H1 bike with Dura-Ace Di2 and Bontrager Aeolus 3 wheels weighs just over 15 pounds.

Aerodynamics and Integration Using an iterative process, Trek took a computer model of the first aerodynamic Madone, launched in 2013, and modified, then tested; then modified some more and tested again. Hundreds of virtual models were created, each one trying to make the Madone a bit more slippery, but always with an eye on the bike’s other performance goals. Bottle placement alone was subject to 140 iterations before arriving at the most aerodynamic position, and Trek claims the Madone is more aerodynamic with bottles than without.

Shadows of the old Madone exist. Geometry is slightly tweaked, and the new Madone’s primary tube shapes are evolutions of the KVF (Kamm Virtual Foil) truncated airfoils introduced in the previous generation. But the new Madone has a much deeper downtube, and aerodynamically shaped seat tube and seatstays where the old used round tubes.

Trek tested the new Madone against the Cervelo S5, Giant Propel, and a Felt AR in the San Diego Wind Tunnel, which Trek considers to be the best and most accurate. Ben Coates, Trek’s road product manager, stressed that the company was pursuing real-world aerodynamics, so all the bikes in the wind tunnel comparison were equipped with two water bottles.

Though the Madone was not fastest at all yaw angles (the S5 and AR eclipsed it at some), Trek’s white paper on the new Madone claims the 2016 Madone is the “overall fastest bike across all yaw angles.” Trek also tested a first-generation Specialized Venge , but didn’t include it in their comparison, “based on data collected from previous test that showed it was not a leader in aerodynamics.” How the new Madone compares to the new Venge is unknown.

Trek’s evaluation then stepped outside the virtual world and the controlled environment of the wind tunnel, and into a velodrome and out on open roads. The claimed results: At 40kph, the new Madone provides a 19-watt savings over a non-aero race bike (Trek used their Emonda as a representative) in a solo time trial situation, and a 14-watt savings when drafting.

To realize these aerodynamic gains, Trek considered more than just the frame, designing dedicated brakes and an integrated bar and stem. The integrated bar and stem saves 34 grams of drag compared to a Bontrager XXX Aero bar, says Trek. The tops are intended to be ridden naked; wrapping them with tape wrecks the bar’s aerodynamics.

More drag savings, up to 37 grams, were realized by hiding the cables. They are run internally through the bar, exiting the stem just in front of the steerer clamp and immediately entering the frame. Except for the rear derailleur loop (or wire) and a tiny bit of rear brake cable, the new Madone has no exposed cables, housing, or wires.

Though the fork’s steerer tube where the stem attaches is effectively 1-1/8” diameter, it is relieved so the cables can enter the frame directly from the integrated bar. While it is possible to clamp other stems to the steerer, it is presently not possible to route the cables properly with anything else, nor use any headset spacers other than those that come with the frame. Speed and integration has its compromises.

For safety, Trek typically recommends that a fork steerer be cut so a few millimeters are exposed above the stem clamp. Doing so requires an extra headset spacer above the stem. The Madone’s stem, however, is designed with the extra spacer built in so the preload cap sits flat for less drag. Trek’s Blendr system accommodates the mounting of computers and lights to the bar.

Trek will offer 13 different versions of the integrated bar; all use the same Bontrager VR-CF variable radius drop, however, you will see some Trek Factory Racing riders with a team-only ergo-bend version. Bar widths are 40,42, and 44, all in 90-120mm lengths, as well as a 42x130.

The center pull brakes are unique to the Madone; no other brake is currently compatible with the frame. The brakes are “designed to seamlessly match the fork and seat stay surfaces, integrating with the recessed areas and allowing air to flow smoothly over the entire surface,” according to the Madone’s white paper. Though the mounting format looks similar to the Shimano direct mount standard—used by the previous Madone and Emonda—it is different enough that only Trek’s brake will work properly.

The dual-pivot brake matches the power of Shimano's excellent 9000-series brake caliper, says Trek, and leverage is adjustable for proper feel and performance with all the major component-maker’s brake levers. Wide rims are no problem, says Coates. Independently adjustable arm position allows the brake to, “work with every rim on the market today.”

After taking a trip down under the bottom bracket on the previous generation, the rear brake returns to the seatstays on the new Madone. Trek says this placement is a bit less aerodynamic, but easier to access and adjust, and, because of the way a wheel flexes, reduces brake rub. Almost all the hardware on both brakes is uncovered and easily accessible, and there is a lever to open the arms for wheel changes. You can’t compensate for brake pad wear by adjusting on the fly with a knob at the housing stop like you can on a typical side pull caliper. Instead, the arms must be moved closer to the rim with a hex wrench.

One of the more curious details of the new Madone are the “vector wings”. Government regulations state that a bike’s front wheel must be able to turn up to 65 degrees from center, even though a rider would almost never turn the bars that far when riding. However, the shape that Trek desired for the head tube, with internal cable routing for the front brake, did not allow this much rotation. The solution was a cover with sprung wings that accommodate this amount of steering. When the bar is turned far enough, the wing is pushed open by the brake; when the bar is turned back, the wing snaps closed.

“Ma-domane” Historically, one of the biggest complaints about aero bikes is an unrefined ride feel. Trek’s solution: Borrow the IsoSpeed Decoupler from the Domane. But Trek ran into a problem in applying it to the new bike: The aerodynamically shaped seat tube (the Domane’s seat tube is round) could not flex enough to provide worthwhile vertical compliance. The solution was to give the Madone a second, internal seat tube.

While the exterior “seat” tube is a structural part of the frame, the seat post is attached to second tube hidden inside the exterior tube. That way, the exposed part of this system is aero shaped, but it transitions to a round, bowed tube inside the frame. Anchored at the bottom bracket shell on one end and with the IsoSpeed decoupler at the top, the interior seat tube can then bend under load, providing about 20mm of vertical compliance; double that of its nearest competitor, claims Trek. Overall, Trek says the 2016 Madone has the same amount of vertical compliance as the Emonda, however, the Domane is about 50 percent more complaint than both.

Trek will offer two seat mast lengths, and two offsets, 5- and 25mm. The saddle clamp is all new, and provides independent adjustment of tilt and fore/aft position.

More Than Just Numbers Echoing a theme we’re hearing more often from more companies, Trek looked beyond just the on-paper numbers when refining the Madone’s feel and handling. The Madone’s white paper, available at Trek’s website, goes into detail on the topic, but here’s a summary based on my conversations with the people involved in the Madone’s development.

To collect real world data about the loads on a bike in typical riding situations, Trek builds aluminum test models and equips them with strain gauges to measure deflection, power meters, and speed and cadence sensors. Test riders subject the bikes to routine events: climbing, sprinting, and cornering, etc., while data recorders collected information from the sensors about the bike’s behavior in response to the events. Trek used this real world data to evaluate computer models, and to be sure the simulations they run on the frames provides an accurate picture of the way a bike would behave in the real world.

Using this method, Trek’s engineers could build several versions of a frame, each having different characteristics. Test riders then provided feedback about each frame’s desirable and undesirable traits. Essentially, the models gave Trek the tools to identify and tune the nuances that add up to what riders call “feel.”

In designing the new Madone, Trek took feedback from its pro factory racing team riders who said they really liked the way the Emonda rode. Thanks to its testing process, engineers had a good idea of what contributed to these positive characteristics, and they built much of that into the new Madone, even though the latter’s tube shapes are much different.

Then, in January 2014, Trek had its factory team riders evaluate three prototypes of the new Madone, each with a different carbon layup. That feedback was taken and used to further develop the new bike. A year later Trek had “full production” versions, again in three different layups, tested by the team again and used the feedback to lock in the final layup of the production 2016 Madone.

At the bike launches I attend, there is almost invariably some slide or discussion about drivetrain, head tube and torsional stiffness and how much awesome-r it is than the previous generation frame and/or competitor’s frames. But Trek’s people didn’t talk much about the Madone’s stiffness at the launch. My impression: They weren’t specifically gunning to achieve a benchmark in a certain test, or notable gains over the previous Madone, or exceed that of competitor’s frames. Their primary concern, I felt, was achieving the ride and handling goals that fulfilled the bike’s purpose, and they seemed quite confident that those goals were met. The resulting stiffness, measured in the traditional ways, is what it is—or so it would seem. They did let on that the Madone is, “a bit stiffer than an Emonda, and less stiff than a Domane.”

The Rest Aerodynamics, IsoSpeed and feel are the three points Trek is emphasizing with the new Madone, but there are other notable details as well.

The frame can accept up to 28mm wide tires. Yes. An aero frame with rim brakes that takes 28mm tires.

The Control Center is flat-out nifty. Found high up the down tube where it is accessible on the fly, it houses an electronic shifting system’s junction box (with Shimano, the junction box button for adjusting trim and to fine-tune shifting is accessible) or, for mechanical, contains a front derailleur cable-tension adjuster. When it’s time to charge the Di2, the charging port is accessed by releasing a catch, popping open the Control Center. Note: The frame is compatible with Campagnolo EPS drivetrains, but the battery must be mounted on the outside of the frame.

Carried over from Trek’s other models is its chain retention device (though the Madone’s is “more aerodynamic,” of course), DuoTrap speed and cadence sensor pocket, and BB92 bottom bracket.

Trek also incorporated a few Easter Eggs into the Madone’s paint. I don’t want to spoil the surprise so I’ll leave them to you to find.

Four complete bikes are offered, three with H2 geometry. All use the same brake calipers and integrated bar. Sizing now mirrors the Emonda. Seven sizes, 50-62cm, are offered in H1; and nine from 47 to 64cm in H2. - Madone 9.2, $6300, built with Shimano Ultegra 11 mechanical and Bontrager Paradigm aluminum wheels; - Madone 9.5 $8400, built with Shimano Dura-Ace 11 mechanical and Bontrager Aura 5 carbon wheels (aluminum brake track); - Madone 9.9 $12,600 built with Shimano Dura Ace Di2 11 and Bontrager Aeolus 5 carbon wheels. Also offered in a women’s version.

Also offered is the Madone Race Shop Limited $13,650, a replica of the bike the Trek Factory Racing team rides, with H1 geometry, Shimano Dura Ace Di2 and Bontrager Aeolus 5 carbon wheels.

The Madone in H1 and H2 fits are also offered through Trek’s Project One paint and parts customization program starting in August. The amazing, hot-pink abomination you see in the photos (note that Trek painted it in the colors I requested) was a H2 Project One dreamed up by yours truly.

Also offered is a frame module–brakes, one-piece bar and stem, and seat mast included–for $5,780 for the H1 and $4,730 for the H2.

How it Rides The new Madone H2 Project One came to the office for a couple of our most experienced testers to spend about a week each on the bike. Off the bat, we were impressed by the bike’s ride quality. One tester compared the bike to the Domane Classic, calling the ride “silky and smooth”; another said there was “good, aggressive-type, road and surface feedback with surprising smoothness—there were no instances of rough chatter over the odd bump.” They also noted that the bike felt very connected to the road, and that even when road conditions deteriorated, the tires tracked and stuck to the ground. The IsoSpeed decoupler gave the feeling of occasionally bottoming out—letting us know that it was indeed working. There was also no brake rub under sprinting, climbing, or pedal mashing.

The new Madone is also surprisingly comfortable: “I could be happy riding it all day, or for an hour crit,” was the comment. The bike handled precisely, and was easy to control over the road.

And of course, it felt fast. On one race-like weekly group ride, a tester observed that he seemed to be able to pedal less than others in the group, all else being equal, and that on a shallow downhill where he normally coasted at a steady speed, he felt like he was actually accelerating.

Overall, the impression came back that the Madone didn’t feel like an aero bike in the ways we typically expect: The ride wasn’t harsh and chattery, the bike was stiff, and while it didn’t feel feathery, it wasn’t heavy, either. As one tester put, “This just felt like a really nice road/racing bike.” And as another said, “It’s just an easy bike to like.”

The Ultimate? Is the 2016 Madone “the ultimate race bike”? Time may tell, but frankly, statements like these are usually unverifiable. Here’s what I know so far: It’s awesome to see Trek finding a bit of swagger and flexing its muscles. I can’t imagine the Trek of just a few years ago going for it they way the company did with the new Madone. This is an impressive bike. And, based on testers’ feedback, it is a great-riding bike. The Bicycling staff races, and loves racing, but we all ride more than we race. And when we ride, we love to go fast on great equipment. The 2016 Madone lets us do both. And it didn’t come cheap or easy—it took a lot of engineering manpower.

.css-1t6om3g:before{width:1.75rem;height:1.75rem;margin:0 0.625rem -0.125rem 0;content:'';display:inline-block;-webkit-background-size:1.25rem;background-size:1.25rem;background-color:#F8D811;color:#000;background-repeat:no-repeat;-webkit-background-position:center;background-position:center;}.loaded .css-1t6om3g:before{background-image:url(/_assets/design-tokens/bicycling/static/images/chevron-design-element.c42d609.svg);} Bike Reviews

The Best Beach Cruisers for Leisurely Rides

The Best Hardtail Mountain Bikes

Best Hybrid Bikes You Can Buy Right Now

The 14 Best Road Bikes of 2024

The Best Commuter Bikes for Getting Around Town

The 10 Best Electric Bikes, Tested by Our Editors

These Folding Bikes Can Go Everywhere

Smoother and Faster: The New Pivot Switchblade

The Best Beginner Mountain Bikes

Reviewed: Colnago's Italian Made C68 Gravel

The 6 Best Kids’ Bikes in 2024

Trek Madone 9.0 brings normal bar and stem to aero super bike

Most inexpensive new madone gets more adjustable cockpit.

You can trust Cyclingnews Our experts spend countless hours testing cycling tech and will always share honest, unbiased advice to help you choose. Find out more about how we test.

This article originally appeared on BikeRadar

New Trek Madone 9 Series gets radically aero for 2016

Trek Madone voted best team bike in 2015 Cyclingnews Reader Poll

Trek Madone Project One Race Shop Limited review

Zubeldia gets custom Trek Madone for final race

Interested in an aero bike but want something with a normal, adjustable cockpit and a pricetag that isn't five figures? Trek's new Madone 9.0 might be what you're after.

Trek Madone 9.0 highlights

• Same frame and fork as $12,000 / £12,000 / AU$13,499 Madone 9.9
• Normal stem and adjustable aero handlebar
• Shimano Ultegra group with Madone Aero brakes
• Bontrager Aeolus Comp Tubeless Ready 50mm wheels
• 50-62cm sizes, four color options
• $3,999 / £3,500 / AU$5,499

The head tube has cuckoo-clock-like panels that hide the upper portion of the integrated caliper

Aero, but...

In late 2015 Trek overhauled the Madone as an ultra-aero race machine, with not only cables but the brakes themselves hidden from the wind. The bike received plaudits from several cycling outlets including BikeRadar for its aero performance and its comfort, thanks largely to Trek's IsoSpeed flex design.

But while the bike managed to avoid the typical buggabo of early aero bikes — they're fast, but they ain't comfy — it did proceed with a typical aero compromise of ergonomic adjustability in favor of an ultra-clean integrated bar/stem that is demonstrably faster.

For context, most major companies with a high-end aero bike sell it with some form of integrated bar/stem, for the same reason: it's aerodynamically faster than a round bar and normal stem by a significant margin. Most companies claim at least a 4-watt improvement. (A good aero bike has a total drag number in the 70-watt range.)

The Madone 9.0 has the same frame and fork as the top-end 9.9, but with a relatively normal handlebar

And while integrated bar/stem cockpits work well for many riders, some people would prefer particular bar shapes, or bar angles, or at least the ability to make changes. With an integrated design, you get what you get.

Integrated pieces have another issue: cost.

Enter the Madone 9.0. Now Trek has an aero bike with the exact frame and fork as the $12,000 / £12,000 / AU$13,499 Madone 9.9, but with a normal stem and an aero but separate handlebar — and a much more attainable $3,999 / £3,500 / AU$5,499 price tag.

Made from the brand's 600 series OLCV carbon the Madone 9.0 sees the H2 geometry — only the Race Shop Limited version gets the H1 fit.

The new Madone bikes all have Trek's IsoSpeed, which is a flexing point where the seatmast joins the rest of the frame

Deep wheels and a compact crank

The Bontrager Aeolus Comp 5 wheels can be set up tubeless but come with 25mm standard clinchers and tubes. Although not as light as all-carbon hoops, the aerodynamics of the metal-rim-with-carbon-fairing design have to be very similar. And you get the more consistent braking of an alloy track.

Current edition Shimano Ultegra continues the Japanese company's fine tradition of an excellent second-tier group that for all intents and purpose functions like Dura-Ace but with a few more grams.

Racers interested in the Madone 9.0 might want to swap out the compact 50/34 crank

One curious spec choice is the compact 50/34 crank. When paired with the 11-28 cassette this is a great everyday setup, but it seems like amateur racers in particular would be drawn to such an aero bike, and might want if not necessarily need a 52/36. If this is a concern, it is likely that your local Trek dealer could swap it out for you.

Thank you for reading 5 articles in the past 30 days*

Join now for unlimited access

Enjoy your first month for just £1 / $1 / €1

*Read any 5 articles for free in each 30-day period, this automatically resets

After your trial you will be billed £4.99 $7.99 €5.99 per month, cancel anytime. Or sign up for one year for just £49 $79 €59

Try your first month for just £1 / $1 / €1

New disc brake-equipped Giant Trinity TT bike spotted at Tour de Romandie

POC Aspire cycling glasses review: A sturdy and stylish modern classic

Tour of the Gila: Tyler Stites wins stage 3 time trial

Most Popular

Like most sites, this site uses cookies to make it work. By continuing to use the site you accept our cookie policy . You won’t be shown this message again :)

You are using a browser that does not support javascript. Some aspects of this site may not work as intended.

We've got 11,000+ bikes in the comparison database. Find another?

• Madone 9 H1

Trek Madone 9 H1 2018

Prove Humanity: Please click here to start .

Measurements are in millimeters and degrees.

• Bike name and year
• Geometry table
• Add an image

Problem?  Flag for Review or

If you like the site, can we ask a favour?

Click now, buy soon, and we'll get a few pennies.

Chain Reaction Cycles - Wiggle - Rose

Thank you! Bob & Dave

Also!   Search by Stack and Reach

You can now search the database by numbers .

Find bikes that match your geometry criteria.

• New comments
• Military Photos
• Russian Military
• Anti-Aircraft
• SA-21/S-400 Triumf

92N6E Radar, S-400

• Oct 18, 2010

Media information

Share this media.

• This site uses cookies to help personalise content, tailor your experience and to keep you logged in if you register. By continuing to use this site, you are consenting to our use of cookies. Accept Learn more…

• What to see
• Elektrostal
• 9th radio centre of Moscow

9th radio centre of Moscow, Elektrostal

#11 among attractions in Elektrostal

9th radio centre of Moscow – popular in the area (distance from the attraction)

Nearby attractions include: Park otdyha, Istoriko-hudozestvennyj muzej, Vystavocnyj zal, Park otdyha.

Park otdyha, Elektrostal

30 min walk • Amusement, Amusement park

Istoriko-hudozestvennyj muzej, Elektrostal

19 min walk • Museum

Vystavocnyj zal, Elektrostal

17 min walk • Museum

24 min walk • Amusement, Amusement park

Shopping Center, Elektrostal

32 min walk • Shopping, Shopping centre

Shop road bikes

Find a retailer.

Notable Places in the Area

Elektrostal Satellite Map

Popular Destinations in Moscow Oblast

Escape to a random place.

• Client log in

Metallurgicheskii Zavod Electrostal AO (Russia)

In 1993 "Elektrostal" was transformed into an open joint stock company. The factory occupies a leading position among the manufacturers of high quality steel. The plant is a producer of high-temperature nickel alloys in a wide variety. It has a unique set of metallurgical equipment: open induction and arc furnaces, furnace steel processing unit, vacuum induction, vacuum- arc furnaces and others. The factory has implemented and certified quality management system ISO 9000, received international certificates for all products. Elektrostal today is a major supplier in Russia starting blanks for the production of blades, discs and rolls for gas turbine engines. Among them are companies in the aerospace industry, defense plants, and energy complex, automotive, mechanical engineering and instrument-making plants.

Headquarters Ulitsa Zheleznodorozhnaya, 1 Elektrostal; Moscow Oblast; Postal Code: 144002

Contact Details: Purchase the Metallurgicheskii Zavod Electrostal AO report to view the information.

Website: http://elsteel.ru

EMIS company profiles are part of a larger information service which combines company, industry and country data and analysis for over 145 emerging markets.

To view more information, Request a demonstration of the EMIS service

• Help Center
• Chat with a Ride Guide
• 1-866-401-9636
• Retail Store
• Bike Services

Reset Password

We will send you an email to reset your password.

Don't have an account? Create an account

Create Account

Already have an account? Sign In

• Favorite your products & save them to your account
• Save a search & get notified when new products drop
• Be first to know about the latest events & promotions

Bike Finder

Results have arrived, trek madone 9.0 road bike - 2018, 60cm, item #brd27791, condition: certified pre-owned what's this, fit range: 6'3" - 6'5" sizing guide, every certified pre-owned bike passes our multi-point inspection.

• Frame integrity verified
• All components inspected
• Drivetrain cleaned and tuned
• Suspension adjusted
• Wheels trued

Our RideFast shipping means this bike gets to you quickly and securely. Domestic US ground rates are a flat $135 for regular bikes or $150 for e-bikes.

Quick Assembly

• Bikes arrive tuned and mostly pre-assembled
• Torque tool & video guide included
• Get riding in 15 minutes

Canadian Customers

Please note that any duties, taxes, or surcharges as required by Canadian customs and provincial authorities will be the buyer's responsibility. Shipping to Canadian addresses may take longer than expected due to customs.

Guaranteed Buyback

We'll happily purchase this bike back from you when you're ready for your next upgrade. A TPC buyback offer is guaranteed for 18 month on all qualifying bikes.

30-Day Returns

If this bike isn't perfect for you, our Ride Guides will help you find the right one.

Engineered for Victory

As the most aerodynamic bike in Trek's lineup, the Madone is built for speed. Utilizing KVF (Kammtail Virtual Foil) tube shapes to cheat the wind, a stealthy brake system hidden away in the front by "Vector Wings", and a geometry that puts you into "go-time" mode, the Madone is your ticket to the top of the podium.

• absoluteBLACK oval chainring for improved rider efficiency.
• New rear brake pads for more braking power.
• Moderate scratches on the drive side chainstay.
• Moderate on the drive side of the top tube & head tube.

Added to Cart

Inspected. Tested. Trusted.

What is cpo.

CPO bikes are gently ridden bikes that have been meticulously inspected, restored and serviced. Every CPO bike is cleaned, tuned and tested in our top-of-the-line Colorado headquarters. Road, mountain, ebike or gravel, TPC services each bike over 8 phases and multiple points of inspection.

Bikes are meant to be used.

Ask a Ride Guide about this

Sizing guide.

The chart below provides a general suggested range of heights and is not exact. Sizing may vary across brands.

The tailoring of any bike is an important step in the long term enjoyment of riding and it can take time to adjust to the fit of a new bike. All contact points (pedals, shoes, and saddle) can be changed and altered for personal preference, performance, and comfort.

Contact our Ride Guides if you have any questions about the fit of your new bike.

866.401.9636 - Contact the Ride Guides

Purchase your next bike with the same confidence you would when buying new. We scrutinize age, condition, and quality. If a bike meets the standard, our pro tune and service will guarantee that your ride will be in pristine condition when it arrives at your door.