pre trip cdl

• Free Practice Tests

Commercial Driving

• Introduction

Getting a CDL

• Fees and costs

CDL Types & Permits

Endorsements & Restrictions

CDL Exam Preparation

Written exams

Practical exams

• Skills test
• Pre-trip inspection
• TSA background check
• Retake policy

CDL Maintenance

ELDT Training & Certification

CDL how-to guides

Join 100,000+ Drivers

• Sponsorship

• Thinking of Becoming a Truck Driver?
• Getting a CDL License
• Trucking Driving Jobs Guide
• Trucking Company Guide
• Trucker Life
• Paid CDL Training
• CDL Schools
• Professional Driving Skills + Knowledge
• Owner Operator
• Latest Articles
• Truck Driver Skills

The Pre-Trip Inspection: A Practical Guide For the Truck Driver

Updated February 24th, 2022

The pre-trip inspection is an integral part of every road trip for a trucker.

It’s probably the most disliked and most often overlooked part of the job of the professional truck driver in the trucking industry.

This inspection is meant to be a thorough check of the truck, trailer and load.

The check is to ensure that everything is in correct working order, prior to the truck and driver, departing on a trip.

Any damage or issues found during the pre-trip inspection which needs attention, must be addressed before departure.

CDL Test Pre-Trip Inspection

 If you just came through the process of getting your CDL, you can breathe a sigh of relief.

You don’t have to check all 500 or so items that you had to memorize for the test every single day.

Out on the road, a thorough pre trip shouldn’t take more than 10 to 15 minutes.

DVIRs – Daily Vehicle Inspection Report

According to federal law ( FMCSR Section 396.11 ), every day, a driver must submit a Daily Vehicle Inspection Report (DVIR) for each power unit he operates. Multiple trailers can go in one report.

DVIRs are either paper or electronic.

Not every trucking company (ahem) enforces this policy, so some truck drivers can go months or years without submitting a DVIR.

Minimum DOT Pre-Trip Inspection Requirements

• Service brakes including trailer brake connections
• Parking brake
• Steering mechanism
• Lighting devices and reflectors
• Windshield wipers
• Rear vision mirrors
• Coupling devices
• Wheels and rims
• Emergency equipment

Your trucking company’s DVIR might be more thorough.

This is a thorough Q&A on DVIRs which you can refer to.

Inspecting a New Truck

When you are assigned a new truck (either daily or just once), there are a few additional things you need to check for on the pre-trip inspection.

Truck Compliance

• Cab card and book – This is a book containing the registration, inspection, permits, cab cards, IFTA paperwork, and any other important papers for the truck. Make sure it is in the truck and all the paperwork is up to date.
• Inspection sticker – This is outside the truck. Find it and make sure the truck is not overdue.
• IFTA stickers – These are the fuel tax compliance stickers. They are on both sides of the truck. Make sure the current year is displayed.
• Elog device – Most trucks are required to have a working elog device.
• Required permits – These are in the cab card book. The most common permits are Heavy Motor Vehicle Trip Permit (Oregon) and the Weight Distance Tax Permit (New Mexico).
• New York HUT sticker – This is usually on the front of your truck. It’s a type of permit.
• License plate – Make sure the license plates on the front and back of the truck match.
• FMCSA Safety Regulations and Hazardous Materials book – These will be given to you by your company. They must stay in your truck within arms reach from the driver’s seat.
• Paper logbook – If your e-log stops working, you must log your hours in a paper logbook, which must be kept in your truck.
• Medical card – You must keep your current medical card in your truck. Always have your CDL on you as well.
• Orange triangles – You must have 3 triangles for when you break down.
• Fire extinguisher – Must be charged and secured to the truck. No rolling around on the floor.
• Extra fuses – If your truck doesn’t use circuit breakers, you must have spare fuses.
• Load bars and/or straps
• Extra oil, coolant, and windshield washer fluid
• Line antifreeze and diesel anti-gel
• Chains and bungees
• Gladhand seals
• Hammer, wrench, wire cutters, cable cutters, knife with glass-breaker

The Class A Pre-Trip Inspection Process

Unless I have to bobtail to pick up my trailer, I inspect my truck and trailer together.

The best way to memorize a thorough pre trip is to do it the same way each time.

Your process will look different from mine, but as long as you are consistent, you will be less likely to miss anything.

I do the inspection first thing each morning as well as every time I swap trailers.

Paperwork and Trailer

• Check the paperwork. It should be the first thing checked when you get to your truck.
• Match the trailer number to your paperwork. If your trailer has a seal, make sure it matches too.
• Unsealed trailer. If your trailer does not have a seal, open it and confirm the product matches the bills. If you are picking up an empty trailer, open it and make sure it’s actually empty.
• Confirm your destination. Ensure the destination is the same as on your trip sheet or load assignment. If there is a discrepancy, call your dispatcher.

I personally like to start with checking under the hood of the rig. Not everyone does, but I do.

Under the Hood of the Truck

I walk around the front of the truck, making sure all the lights work. Then I open the hood.

• Fluid levels – Check all fluids: coolant, oil, power steering fluid, and windshield washer fluid. Make sure caps are tight for the rad, oil filler, power steering fluid and the dip-stick is seated properly.
• Alternator, water pump, power steering pump –Make sure these are in good working order, and the belts are not worn or have too much slack.
• Observe at the engine block.  Check for leaks, fluid running down the side of the engine. Check for wear, cracking or fraying. Inspect fan belts for proper tension and signs of wear.
• Hoses – Check all hoses for leaks, cracks, and tears.
• Wiring – Check wiring for wear.
• Steering linkage – Check linkage for worn or missing parts.
• Tires – Tires should be properly inflated and have decent tread. If there are flat spots on the tire, it needs to be replaced.
• Hub seal – Make sure it’s not leaking and wiped with oil if transparent.
• Brakes – Brake chambers should not be out of round and should be free of grease. Shoes should not be worn down too much.
• Slack adjusters – Pull slack adjuster. If it travels more than an inch, it needs to be adjusted.
• Suspension – Shocks should be in good condition, and not covered in grease or oil.

Back of the Truck

Next, I check the back of my truck because it’s easier to check this before hooking to a trailer.

• Tires – Tires should be properly inflated and have decent tread. If the tires have flat spots, the tire needs to be replaced.
• Suspension – Shocks and airbags should be in good condition, and not covered in grease or oil.
• Drive shaft – Driveshaft should be undamaged and free of grease. Make sure there is no debris in the u-joints.
• Frame – The frame should not have any welds and not cracked or significantly rusted.
• Fifth wheel – The fifth wheel should be properly greased and not broken.
• Fuel tanks – Fuel tanks should not be leaking.
• Stairs and catwalk – Stairs and catwalk should be free of debris and not broken.

Tires should be checked with a tire gauge.

Tip . This is especially if you are slip seating. Tire thumpers aren’t very accurate. If you use a tire thumper, still check with a tire gauge from time to time.

Drives and tandems should be inflated to 100-110 psi and have a minimum tread or 2/32in. Steer tires should be inflated to 110-120 psi and have a minimum tread of 4/32in.

Tires under 50 psi should be replaced, as they can’t retain enough air pressure.

Flat spots can occur from dragging tandems in the winter or when trying to slide the tandems. Tires with flat spots should be replaced.

Check tires for damage, nails, and punctures.

Next, I jump in my cab and start my truck.

• Gauges – Make sure air, oil, and water temperature gauges rise to normal levels.
• Mirrors – Adjust mirrors before moving your truck.
• Windshield wipers – Make sure they work and sit flat against the windshield.
• Horn – Make sure the city and air horns both work.
• Heat and A/C – Check to see if heat and/or air conditioning is working.
• Seat belt – Seat belt should not be frayed and should move freely.

Coupling and Air Lines

This is what could happen if you don’t do the tug test.

The pre-trip inspection is a pretty important thing to do.

Learn your pre-trip procedure and do it when required.

This is why you should always do a tug test when picking up a trailer. The passenger side of the front of the trailer is resting on the frame of the truck and NOT hooked up to the 5th wheel.

The front left corner of the trailer is supported by retracted landing gear only. (Not good!)

The truck driver in this photo (hopefully) learned how critical a pre-trip is. Don’t end up in a pickle like this guy.

Next, I hook up to my trailer.

• Tug test – I back under my trailer until I hear a click, and then immediately do a tug test.

A tug test tests both your coupling and your brakes. If you pull away from your trailer, you aren’t hooked properly.

If you pull your trailer with you, your trailer brakes are out of adjustment. Be absolutely sure to write it up and have it corrected before departure.

• 4 Ways + Headlights. I also turn on my four-way flashers and headlights.
• Airlines and pigtails – Next, hook up airlines and pigtails (electrical connection). Inspect to make sure they aren’t leaking or ripped.
• Visual check of Fifth wheel – Look at the fifth wheel arm under the trailer to make sure it is coupled. The arm should be in.
• Landing gear – Raise the landing gear and check for damage.

Next, I check the bulkhead (front of the trailer).

• Wall – Make sure the wall is not damaged.
• Inspection sticker – Check the DOT inspection sticker to make sure it’s not out of date.
• Registration paperwork – Check the front trailer box to make sure the registration is good.
• Reefer unit – If you are pulling a reefer, select the pre trip function on the unit and run it. It should be completed by the time you are finished your pre trip inspection.

Next step for the pre-trip inspection is to check the side of the trailer and the tandems.

• Lights – Lights should be on and flashing.
• Suspension – springs or airbags should be in good condition, and not covered in oil or grease.
• Tandem pins – Tandem pins should be locked in position, and slider arm should be in its cradle.
• Cables – Make sure the tandem cables aren’t dragging on the ground.
• Underbelly – Make sure there are no damaged beams under the trailer. Check the entire length.
• Mudflaps – Mud flaps should not be torn and hanging.

Back of Trailer

Next, I check the back of the trailer.

• Doors – Doors and hinges should not be damaged.
• Door latches – Doors should be closed and secured.
• Seal – Seal should be intact and match paperwork.
• DOT bumper – DOT bumper should not be damaged
• License plate – Check for the license plate. They tend to wear out and fall off.

Passenger Side

Next, I check the passenger side.

• Brakes – Brake chambers should not be out of round and should be free of grease.
• Suspension – Springs or airbags should be in good condition, and not covered in grease or oil.
• Mudflaps – Mud flaps should not be torn.

Ready to Roll

Finally, I jump in my truck and double check my paperwork and destination.

I release my air brakes, roll forward, and push the service brake.

If everything is good, I’m ready to roll.

Post-Trip Inspection

When I’m done for the day, and every time I swap trailers, I do a post-trip inspection. If I am swapping trailers, I do a pre-trip on the new trailer as well.

A post-trip includes:

• lowering the landing gear
• removing the airlines
• uncoupling, and walking around the trailer checking tires, lights, seal, and mudflaps

Then I finish my paperwork and go home.

Slip Seating

If you slip seat (meaning you are in a different truck each shift), your pre- trip check should be more thorough than if you are permanently assigned a truck.

This also applies to the first inspection after being assigned a truck.

Please be courteous and write up any problems or issues found, so the next driver of the vehicle doesn’t have to deal with it.

Side Note: Clean out your truck and throw away any trash. Common courtesy goes a long way in trucking, between drivers.

Pre-Trip Inspection F.A.Q.

Most breakdowns can be avoided with proper preventative measures, such as daily inspections.

Thorough inspections should be done at the start of each shift. Inspections of trailers should be done every time you swap trailers.

Each driver should do a thorough pre-trip every time they swap drivers.

It should take about 10-15 minutes to perform a pre trip inspection.

The DOT. Make sure you stay in compliance so you don’t end up with hefty fines and an out of service.

The best way to memorize your pre trip inspection routine, is to do it the same way every time. That way you’re less likely to miss something. If you have questions, ask your safety team at your company.

Fluids in the engine, engine hoses and wires, brakes and suspension, mudflaps, trailer registration and inspection paperwork, and license plates.

A Few Trip Planning Tips

• Buy and learn to read a trucker’s atlas. It’s useful to plan routes and avoid restricted roads. I find this road atlas a necessity as a professional truck driver.
• Buy a decent trucking GPS , but don’t rely on it 100%. Use common sense.
• Don’t use the GPS in your elog device. It will put you in a lake.

Please note that minimum requirements for the inspection are established by the FMCSA.

But these may vary by state, trucking company, truck type, and trailer type.

It is your duty as a professional truck driver to perform a thorough pre-trip inspection before each trip and before you drive.

You’ll save yourself from headaches, fines and unnecessary accidents.

More Articles You May Like

• Trucking Terms – A Guide to Our Industry’s Lingo
• The 18 Wheeler – A Comprehensive Guide to Big Rigs

CDL Truck Driver Skills – Tips, Tricks + Knowledge to Kick Your CDL Skills Up a Notch!

• The D.O.T. Physical- A Guide For the Truck Driver

Everything You’ll Want To Know About Paid CDL Training

Custom Big Truck Sleepers Photo Gallery Collection

The Best Trucking Companies to Work For 2024 USA

5 Best GPS For Truckers – A Professional Driver’s Guide

Twice a month we email you the best tips and new articles to help you better navigate the trucking industry..

10 Truck Driving Safety Tips Every Professional Driver Should Follow

A veteran 40+ years truck driver shares 10 of the all time, tried and true truck driving safety tips ALL professional truckers should know AND follow! If every driver of EVERY vehicle on the road followed these safety tips, our roads would be SO much safer.

Trucker Tips Master Guide: Expert Advice From Experienced Truck Drivers

A collection of trucker tips from million milers and experienced drivers. These are gold nuggets for the new truck drivers!

Instruction, clear advice, videos and photos for truck driver skills, maneuvers and information for all professional truck drivers.

A practical guide to paid CDL training programs. Recommended Company Sponsored Schools, Requirements, pros + cons, what to expect from company-sponsored cdl training programs.

Is a Career As a Department of Defense Truck Driver For You?

As a Department of Defense (D.O.D.) truck driver, your role is integral to the logistics and supply chain operations of […]

Navigating Fair Truck Driver Pay: Are You Earning Enough?

Ready to take control of your truck driver pay? Discover key factors impacting your earnings and ensure you’re compensated appropriately […]

The Best Tanker Trucking Companies to Work, U.S., 2024

Top Tanker Trucking Companies in the US To Work For Tanker work typically falls to the ‘better carriers’.  Tanker carriers […]

Best Flatbed Trucking Companies, US, 2024: Our Top Picks

There are over 1 million truck drivers working for flatbed trucking companies in the U.S. trucking industry. However, not all […]

Best Trucking Companies For New Drivers in the U.S., 2024

For new drivers entering the trucking industry, diving into the right pool can make all the difference. The foundation of […]

Follow Smart Trucking

• Register / Login
• Trucker's Forum
• Paid CDL Training
• Truck Driving Jobs
• CDL Practice Tests
• High Road Training
• Truck Driver's Career Guide Chapter 5

• Truck Driver Pre-Trip Inspection

The Complete Guide To A Career In Trucking

What does the pre-trip inspection exam include.

You will be expected to be able to perform a complete pre-trip inspection on your vehicle, including both in-cab & external features, as well as the engine compartment.

Fluids, belts, brakes, air brakes, and lights are some of the main components to the test.

The pre-trip inspection will ensure that the vehicle that you are operating is safe and road-worthy to drive.

The In-cab pre-trip inspection:

This section will demonstrate that you know how to check that all in-cab functions are operational, including lights, gauges, etc., and ESPECIALLY the air brakes.

Pre-Trip Inspection - My Way! A must see!: In-Cab Pre-trip Inspection

This Pre-Trip is done on my truck and trailer. I physically took the pictures and edited them to my liking. It is a complete Pre-Trip Inspection and features everything you'll need to know.

Video - PreTrip Inspection - Interior Cab

This video shows how to do an in-cab pre-trip inspection

Video - Srtda in cab pre trip and brake test

This video shows how to do an in-cab pre-trip inspection and brake test.

The External pre-trip inspection:

You will be expected to check lights, tires, rims, fluids, belts, etc. Generally, all the components on the outside of the truck & trailer, including the engine compartment.

Forum - Daniel B.: Pre-Trip Inspection - My Way! A must see!

As stated, these are solely based off of how I like to do the Pre-Trip. I give my personal opinions as well as some helpful tips. Your Instructors advice may vary. In the end, just do it the way your Instructor wants you to do it.

Pre-Trip Inspection Video By Apex CDL Institute

This is a complete Pre-Trip inspection video by Apex CDL Institute

Pre-trip checklist, practice exams, and memory aids:

Pretrip Inspection Study Guide

The purpose of the Pretrip Inspection is to be able to do a thorough safety inspection on a commercial vehicle before heading out onto the highway.

Pre-Trip Inspection Free CDL Practice Tests

Our free Pre-Trip Inspection cdl practice questions are designed to help test your knowledge of the CDL Manual and sharpen your skills for taking the CDL permit and endorsement exams.

Why Join Trucking Truth?

• The High Road Training Program
• The High Road Article Series
• The Friendliest Trucker's Forum Ever!
• Email Updates When New Articles Are Posted

Apply For Paid CDL Training Through TruckingTruth

Did you know you can fill out one quick form here on TruckingTruth and apply to several companies at once for paid CDL training? Seriously! The application only takes one minute. You will speak with recruiters today. There is no obligation whatsoever. Learn more and apply here:

• Privacy Policy

Full pre-trip inspection on your Class A truck for the new CDL road test

This video will explain the full pre-trip inspection on your Class A truck for the new CDL road test. Watch the whole thing to learn the new pre-trip.

CDL Driving Academy is the GREATEST CDL school available in the United States. We offer training for your CDL permit, simulation training with our state-of-the-art trucking simulator, AND hands-on yard and road training to prepare you for your CDL road test. If you are looking to get a CDL and want to train with only the BEST CDL school, give us a call TODAY to get started on your ROAD TO FREEDOM with your new career!

For the CDL Class A Road test, the CDL Class A Pre-Trip Inspection is the hardest part. The reason most people fail their CDL CLass A Road Test is because they do not get the right CDL Class A training and that makes them fail the Pre-trip inspection. The Road Test is split into 3 different sections the first part of the CDL Class A road test is to pass the CDL Pre-trip inspection you are going to be asked to do both an Inside air brake test as well as an Outside pre-trip inspection. The second part of the CDL Class A road test is a skills test. The student will have to master six different parking maneuvers and the last part of the CDL Class A road test is the road driving. This test will take two and a half hours to complete however it all starts with this CDL pre-trip inspection.

Most people fail in the first 10 mins of the test because they did not get the proper CDL Class A training on the pre-trip inspection. That is why we have created this video to show you how our students at Driving Academy get the proper CDL Class A training they need in order to pass the CDL Class A Road Test. We offer this video and much much more to our students when we train them for their CDL Class A Pre-trip Inspection. Our students get our highly trained instructors to help them with the CDL Class A pre- trip inspection, they also get a word for word script on exactly what to say during their CDL Class A Road test, and they also get to practice on the same CDL Class A truck that they will be taking their test in as well. After our CDL training program our students are ready to take this test and become successful CDL Drivers and start making Big Money. After our students pass the CDL Class A Pre-trip Inspection they get help with our free life time job placement program. This is where it is our Job to help Students find their CDL Class A Job. Once they Get their CDL Class A Job they will have to do the CDL Class A Pre Trip Inspection if they have followed our training and plan to be the best CDL Class A Driver they can be. They will Learn that when they do their CDL Pre-Trip inspection on a daily basis they will be able to catch things when they are small and fix them so it does not cost them too much money or time at their CDL Class A Job.

CDL DRIVING TEST/ CDL ROAD TEST/ CLASS A PRE-TRIP INSPECTION CDL ROAD TEST/ CDL PRE TRIP/ PRE TRIP INSPECTION CLASS A/ PRE TRIP INSPECTION TEST / CDL PRE TRIP INSPECTION CLASS A / CDL INSPECTION

You may also like